I cut the price! 2021/3/10 Selling price 19,800 yen ※ It is cheap because of poor condition. Flat-front vial horn for small and lightweight type It helps to make horizontal characteristics constant and to correct driver characteristics. It is a horn that stretches well in the middle range, and it is difficult to get noisy feeling in the high range. It is suitable for a slightly smaller system. (Kimiya Miura)
Accessories: No accessories
Main Specifications: Throat Diameter 25mm Compatible Driver 2426H/J Use Minimum Frequency 500Hz Recommended Lowest Crossover Frequency 630Hz High Density Polyurethane W448 x H173 x D174mm 1.4kg
The price has been reduced. This is an ALTEC 1.5-inch horn with a sales price of 20,000 yen 288 etc. for 2022 4/5. The sound has vertical momentum, and although not wide range, the energetic sound is excellent. Overall, there is a feeling of use such as small scratches (Itsuro Mizushima)
Accessories: none
Main Specifications: Mantalay Horn Polyester Fiberglass Recommended Crossover 500Hz Compatible Unit/288/291 Series W324 x H327 x D317mm 1.6kg
The price has been reduced. 2022/8/27 selling price 12,000 yen A short horn of unknown manufacturer that can be attached to a 1-inch driver of JBL. Deadening has been applied to the metal body to make a sound skip. There is a lot of feeling of use (Hitoshi Kobayashi)
Accessories: none
Main specifications: W380 × H164 × D280 mm
The disposal price has been reduced! (Member discounts are not applicable) 2022/3/23 sales price 15,000 yen Unspecified bi-radial horn. It feels like an EV when I saw it. It is possible to mount JBL 2-inch screwdrivers, etc. The appearance is dull. (Eiji Tamura)
Accessories: No accessories
Main specifications: W440 × H290 × D150mm own weight 1.06 kg/book
CORAL acoustic lens AL-601 is in stock. It is compatible with tweeters with horn opening diameters up to 60mm, such as H-60. Since the frequency of the sound becomes narrower as it gets higher, it is used to diffuse the sound and compensate for the lack of radiation angle in the treble. Overall there is Kusumi ※ The block behind is not included (Shota Sasaki)
Accessories: Nothing
Main specifications: Diffusion angle/horizontal 80 degrees Vertical 45 degrees Effective frequency 3 KHz or more compatible Horn caliber 60 Φmm or less width 130 × height 92 × depth 35 mm Weight 130 g
A short horn used in the 43 series. It can also be built into an enclosure, but you can hear good sound even if you attach a screwdriver and place it on top of the enclosure. There is paint peeling on the exterior. Serial 40483/40685 (Yonejima Satoshi)
Accessories: no accessories
Main specifications: 80 degrees horizontal and 45 degrees vertical orientation for 1" drivers Recommended crossover 1.2 kHz baffle opening diameter 108 mm depth 216 mm
Straight Short Horn for 1" Driver It is a long-used standard model that is used in a variety of speakers. Appearance has scratches, dullness. Serial 13363/17760 (Kimiya Miura)
Accessories: No accessories
Main specifications: Directional characteristics 90( horizontal) /45( vertical) throat diameter 2.5cm crossover frequency 500Hz or more horn total length 216mm 1.1 kg/1
Acoustic lens installed on JBL monitor speakers such as 4343 series. By wearing it, it moderately diffuses and calms the sound of too strong horn. There is no velcro on one side The appearance has dirt and dullness as a whole. (Yoichi Murakoshi)
Accessories: none
Main specifications: Directional 80 degree x 45 degree (measuring 2307, 2311 horn mounted) W254 × H156 × D63mm 0.5kg
* It is inexpensive because the paint deteriorates. Compact and lightweight flat front bi-radial horn. It helps to keep the horizontal characteristics constant and to correct the characteristics of the driver. It is a horn that stretches well in the middle range and makes it difficult to feel noisy in the high frequencies. It is suitable for slightly smaller systems (Tetsuji Oikawa)
Accessories: none
Main Specifications: Throat Diameter 25mm Compatible Driver 2426H/J Use Minimum Frequency 500Hz Recommended Minimum Crossover Frequency 630Hz Made of High Density Polyurethane W448 x H173 x D174 mm 1.4kg
The price has been drastically reduced. 2023/6/25 sales price 15,000 yen This horn was used in Tesco's mid-range speaker system PS-2000H. It was equipped with a 1 inch driver. There are 3 screws for attaching a screwdriver. The Altec 2" driver did not fit. Specs and details are unknown. There are paint drops in places (Murakoshi Yoichi)
Accessories: none
Main Specifications: Mounting screw - screw position 87mm W655 x H232 x D480 mm 7.6 kg
I cut the price. 2021/8/28 selling price 20,000 yen* Green painting. ONLY ONE ALTEC's classic 4 sectoral horn for 1 inch. You can enjoy the horn sound unique to ALTEC with your favorite 1-inch driver such as 802-8D. (Hirotsugu Kondo)
Accessories: None
Main specifications: crossover 500Hz directional horizontal 90° x vertical 40° throat diameter 250mm
W600 × H270 × D475mm 5.8kg
Aiden 1" aluminum radial horn There are bald paint, small scratches (Oikawa Tetsuji)
Accessories: none
Main specifications: W290 × H140 × D225 mm 1.6 kg (actual measurement)
Short horn used in 4343, 4344. It can be built into an enclosure, but it also sounds good in the style of attaching a driver and placing it on top of the enclosure. The appearance may be dull and some paint peeling. Serial 15638/15694 (Satoshi Yonejima)
Accessories: Mounting screws
Main specifications: Directional horizontal 80 degrees, vertical 45 degrees recommended crossover for 1 inch drivers 1.2kHz baffle opening diameter 108mm depth 216mm
Straight Short Horn for 1" Driver It is a long-used standard model that is used in a variety of speakers. (Itsuro Mizushima)
Accessories: None
Main specifications: Directional characteristics 90( horizontal) /45( vertical) throat diameter 2.5cm crossover frequency 500Hz or more horn total length 216mm 1.1 kg/1