※It is inexpensive because there are many stains. A classic shell made from machined aluminum blocks. I like the sturdy construction and simple design (Murakoshi Yoichi)
Maintenance information: 2024.5.21 continuity confirmed
Accessories: none
Main specifications: machined aluminum block body weight 13g
Maintained! Woofer unit used in A5. It is a 38cm Alnico magnet, and the open sound is truly Altec. There are repair marks on the edge (Sasaki Shota)
Maintenance information: 2024.5.23 Maintained (voice coil, grommet, tinsel, and connection terminal parts were polished, connected with aluminum solder, and improved contact. Edge crack repair)
Accessories: none
Main specifications: 38cm cone woofer unit impedance 16 ohms output sound pressure level 104 dB 12.4 kg
Pickering's classic headshell. The aluminum press finish has just the right amount of sound. The overhang is adjustable, and the wide mounting width makes this model easy to use. There is a slight screw scratch. (FUJISAWA KOSHI)
Maintenance information: 2024.5.23 continuity confirmed
Accessories: No accessories
Main specifications: aluminum stamping weight 8.2 g
This is an adapter for a NAGAOKA doughnut board. I use it for EP playback, but the machined aluminum gives it a sense of luxury. There is a small scratch. (FUJISAWA KOSHI)
Accessories: No accessories
Main specifications: machined aluminum, diameter 40 x height 9 mm, weight 20 g
The price has been reduced. 2023/8/29 sales price 24,800 yen The stylus is good, but it's cheap because the cantilever is curved. A mono cartridge with a traditional 33 series body. Play mono records clearly with horizontal pickup only. It has vertical compliance and is optimized for recurrent mono discs from the stereocar era. You can feel that the range is wider than Denon's DL-102 (Fujisawa Yukishi)
Maintenance information: 2023.8.29 Operation confirmed
Accessories: needle cover
Main specifications: MC type needle pressure 2.3 to 2.7 g (2.5 g standard) Muku round needle high hardness duralumin cantilever PCOCC coil anti-vibration rubber “Honeynight” impedance 10 Ω 6.9 g
*The 2-tier rack decoupler spike holder is not included. You can see the attention to design and sound quality at a high level, such as slits that have been carefully thought out for heat dissipation effects and resonance, and solid aluminum pillars. There are some threads and bumps on the exterior (Tamura Eiji)
Accessories: none
Main specifications: W597 x H455 x D475 mm between shelves 326 mm
An ultra-high purity 6nCu with a digital RCA cable 1.0m pure silver coating is used as a single wire. Double shield structure with soft copper wire braids layered on top of aluminum PET tape. A two-layer sheath structure that controls unnecessary vibrations by covering the outer circumference of the shield with a RoHS-compatible PVC sheath. The exterior is generally beautiful with no conspicuous scratches (Tamai Jun)
Maintenance information: 2024.5.20 continuity confirmed
Accessories: original box
※1 bottle only. Super tweeter using an aluminum alloy thick cylindrical horn and an ultra-lightweight ring diaphragm. It expands the well-stretched, clean high frequency range. There are small scratches and dullness on the exterior. (YONEJIMA Satoshi)
Maintenance information: 2024.5.8 oscillator check is good
Accessories: pedestal, instruction manual
Main specifications: Alnico magnet, 8Ω, playback frequency band, 5kHz to 35kHz, output sound pressure level, 106dB, recommended crossover, 7kHz or higher, input 50W, 800g/book
The price has been reduced! 2024/5/14 sales price 55,000 yen direct drive analog turntable. Equipped with a knife-edge tone arm in collaboration with SAEC. A Sumiko Oyster cartridge is also included, and it also has a built-in phono equalizer, so you can enjoy records right away. The exterior is good with no noticeable scratches. Serial 2280200 (Fujisawa Yukishi)
Maintenance information: 2024.5.14 Operation confirmed
Accessories: instruction manual, AC adapter, connection cord, cartridge, head shell, original box
Main specifications: direct drive aluminum die-cast static balance type S-shaped tone arm length 223 mm needle pressure variable range 0 g to 5.0 g applicable cartridge mass 3.0 g to 12.0 g, 14 g to 23 g (including attached headshell) cartridge part: mm type output voltage 4.0 mV needle pressure 1.5 to 2.5 g mass 5.3 g analog output terminal: RCA pin jack (phono/line switching type) W420 x H117 x D356 mm Weight approx. 6.1 kg
The price has been drastically reduced! 2023/5/16 sales price 118,000 yen with LS STAND 70 (list price 48,000 yen). This model won the Audio Famous Equipment Award 2005 Speaker System Small Category Award. An excellent balance between the robustness of the enclosure and the suppleness of the unit group. A practical model with attractive spatial expressiveness and accurate sound images that don't make you aware of the presence of a speaker. There are scratches and bumps on the exterior. Serial 37038E002557/37038E002558 (Yonejima Satoshi)
Maintenance information: 2024.5.15 sweep test good
Accessories: instruction manual saran net spike fixing screw
Main specifications: 2-way bass reflex woofer 115mm aluminum hybrid cone tweeter JETIII crossover frequency 3,000 Hz input rating 70W/maximum 90W frequency characteristics 42-50,000 Hz efficiency 86dB impedance 4Ω dimensions W123 x H208 x D282 mm (when grille attached) weight 6.5 kg LS STAND 70: H700 x W240 x D290 mm top plate W75 × D210mm weight 6kg/set
Fidelity-Research headshell Lightweight and highly rigid. It is characterized by an enveloping shape with a thick aluminum press-processed body. There are dullness and small scratches on the exterior (Murakoshi Yoichi)
Maintenance information: 2024.5.19 continuity confirmed
Accessories: none
Main specifications: aluminum stamping dead weight 10g
The price has been drastically reduced. 2024/5/15 sales price 118,000 yen Maintained! A famous direct drive machine representative of Technics. The torque is high, the start and stop times are extremely short, and the stable operation that immediately enters constant speed is unique. It also drives LP heavyweights without difficulty. Overall there are small wounds, dullness, etc. (Oikawa Tetsuji)
Maintenance information: 2024.5.15 Maintained (due to disconnection of the FG coil in the motor core, the FG/ angular velocity detection coil was taken out after disassembling the motor core, and the coil pack was rewound. The rotation speed has been reset)
Accessories: copy of instruction manual, power supply unit
Main specifications: Direct drive aluminum die-cast turntable 33, 45, 78 rotating body W365 x H100 x D360 mm 9.5 kg power supply unit W110 x H85 x D300 mm 3.8 kg
The price has been reduced. 2024/4/29 sales price 110,000 yen The 3 channel 5 units are nicely put together in one package. In addition to the fact that a rich sound field can be simply played back via Bluetooth, etc., it is a product with an emphasis on functionality that can also be enjoyed with analog. Recommended for studio users. Other than the exterior and stains on the top plate, it's fine (Kobayashi Hitoshi)
Maintenance information: 2024.4.29 Operation confirmed
Accessories: remote control, power cord
Main specifications: 33mm pure pulp cone woofer x 2, 25mm aluminum dome tweeter x 2, 100mm pure pulp cone center midrange x 1 input HDMI (ARC), 3.5mmAUX, RCA Phono (MM), Ethernet/WiFi Bluetooth playback frequency characteristics 45Hz to 25kHz (-6dB) W790 x H216 x D287mm 15.9 kg
Over 300 deteriorated parts, including 133 transistors and 65 capacitors, have been replaced and maintained! Shell (AT-LH15/OCC) with cartridge (AT-F3/2). A supreme record player made by combining the best of Yamaha's engineering. In addition to adopting a linear tracking system, what is surprising is the amount of material that was put in without hesitation. The total weight of the main body alone is 27 kg, and the turntable made of super duralumin cut from solid wood weighs 5.6 kg. The well-structured low range and the delicate, clean sound that spans the entire range are remarkable. The smooth operation feeling of auto play and multifunctionality such as pitch control are also attractive. There are small scratches and dullness, but it is a beautiful category even when viewed from the model year (Oikawa Tetsuji)
Maintenance information: 2024.5.14 Maintained (replacement of deteriorated parts, re-soldering of each board, board cleaning, volume disassembly cleaning, circuit adjustment of each part, operation check, sound test)
Accessories: power supply unit, screw, shell (AT-LH15/OCC), cartridge (AT-F3/2)
Main specifications: Direct drive system motor 20 pole 15 winding slotless DC motor tone arm/dynamic balance linear tracking arm mounting cartridge dead weight range 4 to 13 g rated power consumption 27 W body/W480 x H154 x D416 mm 27 kg power supply/W124 x H90 x D385 mm 5 kg
The price has been drastically reduced. 2024/5/4 sales price 398,000 yen Glass panel brand new replacement included maintenance! A pre-main amplifier with a built-in McIntosh traditional output transformer. You can enjoy the rich and rich sound world typical of Macintosh. This is one that combines the sound appeal of modern and old McKinn. The sense of power that makes you feel the strength is similar to that of a separate amplifier. The exterior is good without any major noticeable scratches (Oikawa Tetsuji)
Maintenance information: 2024.5.3 maintained (panel dismantling and replacement, meter, illumination lamp replacement, in-board C deterioration replacement, RCA cleaning, SW, VOL cleaning, operation check, backup power supply transformer pattern, relay pattern solder crack correction)
Accessories: remote control, copy of instruction manual
Main specifications: 150W+150W (8/4/2Ω) phono input MM dimensions W445 x H179 x D508 mm weight 30 kg
Audio-Technica headshell of unknown model number. Simple aluminum press processing. There is a feeling of use such as rust on the finger, small scratches on the main body, peeling paint, etc. (Murakoshi Yoichi)
Maintenance information: 2024.5.7 continuity confirmed
Accessories: none
Main specifications: 8 g dead weight
※1 bottle only. A full range unit that combines an aluminum alloy HR diaphragm and a pure magnesium ridge dome diaphragm. Compared to conventional paper units, it has a slightly better transparency and microwave feel. The exterior is stained with corn paper, paint marks and scratches on the frame (Satoshi Yonejima)
Maintenance information: 2024.5.6 sweep test is good
Accessories: original box
Main specifications: impedance 4 ohms minimum resonance frequency 72 Hz playback frequency band F0 to 10 kHz output sound pressure level 85.5 dB
Comes with a magazine! A full-range unit from Stereo magazine's 2016/8 appendix. Uses Fostex's first aluminum cone diaphragm and center cap. It features good sounding and sharpness. (FUJISAWA KOSHI)
Maintenance information: 2024.5.2 operation confirmed
Accessories: gasket, magazine (original box)
Main specifications: 8cm full range unit impedance 8 ohms minimum resonance frequency 105 Hz sound pressure level 82.5 dB
The price has been reduced. 2024/4/26 sales price 12,800 yen. This is a rare KEF center speaker Q6C in stock. It is a well-balanced and well-organized sound character typical of the Q series. It seems to express a sufficient sense of sound field even when used in combination with Q1 for theaters. There is a bruise on the upper back corner. Serial 2027685G (Murakoshi Yoichi)
Maintenance information: 2024.4.25 sound output confirmed
Accessories: jumper plate, saran net
Main specifications: 2-way bass reflex low range/130mm Uni-Q high range/19mm Luminiumdome frequency characteristics 50Hz-27kHz crossover frequency 2.8kHz 89dB 8Ω W432xH160xD215mm 4.1 kg
Technics machined aluminum EP adapter It's a convenient item to have for listening to singles. There is a feeling of use such as dullness (Hiroki Aso)
Accessories: none
The price has been drastically reduced. 2023/12/11 sales price 15,000 yen*There is no problem with operation, but since it is cheap, it is being delivered as is. Center speaker for the company's STAGE series. Please help build a theater system (Daiki Goto)
Maintenance information: 2023.12.11 operation confirmed
Accessories: instruction manual
Main specifications: 2-way dual 133mm woofer, 25mm aluminum treble unit impedance 6Ω efficiency 88dB W469 x H190 x D220 mm weight 7.95 kg
Maintained! A system equipped with DENON's highest-model phono motor DP-80 at the time and DA-401 tonearm mounted on a genuine cabinet DK-300. You can enjoy music slowly with stable operation by combining the DP-80, which incorporates plenty of advanced technology from the time, such as a dual-structure turntable and AC servo motors, and the DA-401, which prevents the needle from being violently touched by the influence of record boards by reducing weight. There is a feeling of use on the exterior, such as dullness and small scratches. Serial 118435 (Hiroki Aso)
Maintenance information: 2024.4.22 maintained (TR replacement normal/variable SW repair power capacitor replacement speed adjustment sound output test)
Accessories: copy of the dedicated shell instruction manual
Main specifications: DP-80 quartz lock direct drive outer rotor 3-phase AC servo motor, double structure, aluminum die-cast turntable, compatible with 33/45 rotations, DK300 dimensions W550 x H190 x D470 mm, DA401 static balance type, effective length 244 mm, needle pressure range 0 to 2 g, total weight approx. 24 kg
The price has been drastically reduced. 2024/2/12 sales price 89,800 yen ※It has been replaced with a non-genuine edge. You can enjoy voluminous bass with highly efficient and heavy cone paper. It is also durable with a gathered edge, and is also recommended for backload and front load enclosures. There are viscoid sagging marks (Oikawa Tetsuji)
Maintenance information: 2024.2.12 Operation confirmed
Accessories: none
Main specifications: rated input 150 W frequency characteristics 30 Hz to 2 kHz 16 ohms efficiency 96 dB crossover frequency 800 Hz recommended enclosure volume 170 to 225 liters depth 146 mm 7.5 kg
An aluminum-pressed headshell very similar to SME's S-2 and Sansui. It is a split finger type. There is a mark where the logo has come off on the front (Murakoshi Yoichi)
Maintenance information: 2024.3.7 sound output confirmed
Accessories: none
Main specifications: dead weight 9g
Good condition with original box! OTG cable compatible with portable devices equipped with Lightning terminals. Can be used with products equipped with USB Type-C. By using a mesh sheath that is resistant to compression and twisting, and aluminum alloy is used for the plug, faster and more stable transmission is achieved. (FUJISAWA KOSHI)
Maintenance information: 2024.2.6 continuity confirmed
Accessories: original box
Main specifications: Lightning-USB TypeC total length 138mm cable length 80mm (excluding plug)
The disposal price has been reduced. Member prices are not applicable. 2023/9/23 sales price 118,000 yen This is a high sound quality studio preamp with feedback on design and development technology for professional consoles and DC power amplifiers. It has a high-grade design, such as an input level equipped with a large machined aluminum knob, monitor level volume, an R core transformer, and a luxurious power supply unit using a large capacity capacitor. There are hit scratches and line scratches overall (Daiki Goto)
Maintenance information: 2023.9.23 Operation confirmed
Accessories: power cable
Main specifications: Input SOURCE INPUT 4 stereo systems (1 of which is balanced input) DECK INPUT stereo 4 systems output MONITOR OUTPUT stereo 2 systems (1 of which is balanced output 2 hot) DECK OUTPUT stereo x 4 W483 x H181 x D44 mm 3.4 kg
USB Cable 0.5m SUM USB A/USB MiniB Type Silver Clad OFC High Purity Copper x Conductors, 6 Aluminum Diecast Connectors, 24 Gold Plated Terminals, Wide Base, Features Soft Sound, Rich Bass, and is Recommended for making classical music resonate loudly. There are scratches on the plug shell (Kojima Yosuke)
Accessories: none
2-row 6-piece outlet plate made of corrosion-resistant aluminum alloy+fully coated new metal There is a feeling of use such as small scratches (Kanai Hidetsugu)
Accessories: none
Main specifications: W120 x H116 x D6.5 mm weight 38 g
Outlet plate for 2 rows of 6 using corrosion-resistant aluminum alloy+new metal with full coat processing (Hidetsugu Kanai)
Accessories: none
Main specifications: W120 × H116 × D6.5 mm Weight 38 g
Outlet plate for 2 rows of 6 using corrosion-resistant aluminum alloy+new metal with full coat processing (Hidetsugu Kanai)
Accessories: none
Main specifications: W120 × H116 × D6.5 mm Weight 38 g
Outlet plate for 2 rows of 6 using corrosion-resistant aluminum alloy+new metal with full coat processing (Hidetsugu Kanai)
Accessories: none
Main specifications: W120 × H116 × D6.5 mm Weight 38 g
2-row 6-piece outlet plate with corrosion-resistant aluminum alloy+full coated new metal. There is no problem with the appearance (Kanai Hidetsugu)
Accessories: none
Main specifications: W120 × H116 × D6.5 mm