Unspecified speaker stand. Recommended for 4312 and NS1000M size speaker users. Appearance, dullness, scratches, and a feeling of use can be seen (Kobayashi Hitoshi)
Accessories: none
Main specifications: main body: W350 x H300 x D330 mm 5.2 kg (actual measurement) Top plate: W320 x D300 mm (actual measurement)
The price has been reduced. 2024/1/5 sales price 400 yen. ※1 bottle only. 3 cm unit with unknown details. Since the size and condenser is attached to the plus side, it seems to be a tweeter. The appearance is good with little feeling of use (Kobayashi Hitoshi)
Maintenance information: 2022.11.15 Operation confirmed
Accessories: none
Main specifications: actual impedance measurement 3 ohms 3 cm
The large triode print sold in Japan has disappeared, but I think it was made by NEC from the structure. Measured IP value: 45 mA (the best standard IP value for this amplifier is 50 mA) with the original box ※ I checked the sound output with the test amplifier and measured the plate current value, and it has been determined that the operation is good (Kojima Yosuke)
Accessories: original box
※There is a TELEFUNKEN ECC803S, but from the structure, it was determined that the printing is CV4004, the printing is a reprint. The plate is not a box type, only one side of the rib plate is rib plate sold per bottle ECC83/M8137 equivalent tube measurement value 44 (rejection value 32) with replacement box ※ The measured value represents the GM value measured with the test machine TV-7 (Kojima Yosuke)
Accessories: replacement box
The price has been reduced! 2024/2/8 sales price 1,000 yen Compatible replacement needle for AUREX MM cartridge C-550/2. The standard needle is a carbon fiber cantilever, which is presumably made of metal. Sound was made using C-550/2 (Takahashi Nobuyuki)
Maintenance information: 2024.2.8 operation confirmed (sound output on C-550/2)
Accessories: none
※One piece only. Details unknown, this is an ALTEC 604 or ALTEC 1 inch driver diaphragm. It seems to be an inexpensive interchangeable product (Daiki Goto)
Accessories: none
※1 XLR male to phone jack cable 1.5 m interconnect cable with unknown manufacturer The terminal is male and cannot be used as a microphone. There are a few indelible writing marks left on the plug (Kanai Hidetsugu)
Maintenance information: 2023.9.18 Conductivity confirmed
Accessories: none
Unspecified set of 2 wood blocks 30mm square insulator cube It is similar to Yamamoto Sound Crafts's QB-1, but it is smaller than the QB-1 and the details are unknown. You can see the exterior, dullness, and feeling of use (Kobayashi Hitoshi)
Main specifications: W30 x H30 x D30 mm 28.6 g (actual measurement)
Unspecified board. A leather-style decorative sheet is attached to a wooden board (Tetsuji Oikawa)
Accessories: none
Main specifications: W530 x H25 x D430 mm, weight 3.4 kg (actual measurement)
XLR female to mono mini jack cable 4.5m unusual combination microphone cable. Can also be used as a normal microphone cable using standard jack conversion (Murakoshi Yoichi)
Maintenance information: 2024.4.11 continuity confirmed
Accessories: none
The price has been reduced. 2018/3/3 selling price 10,000 yen Technics ring for fixing horns. Recommended for self-made people (Oikawa Tetsuji)
Accessories: none
Main specifications: Inner circumference diameter 95mm (actual measurement)
※There is no compatible cartridge, so it has not been checked. Synthetic diamond round needle is a replacement needle that can be used with SHARP (Optonica) record cartridges. If you use it, be sure to use it as a stock. The exterior has a feeling of use such as dullness (Jun Tamai)
Maintenance Information: 2024.4.28 Operation Unchecked
Accessories: none
Main specifications: mm needle pressure 1.5g
Unspecified power cable 2.0m. The plug is Panasonic WF5018K, and the connector is made by Global Electronics. This cable is relatively easy to handle. The exterior is dull and has a feeling of use (Takahashi Nobuyuki)
Maintenance information: 2024.5.5 continuity confirmed
Accessories: none
Unknown wood cabinet. Cushioning material is attached to the inside. There are small scratches and dull stains (Sasaki Shota)
Accessories: none
Main specifications: W470 x H120 x D390 mm Weight 1.8 kg (actual measurement)
The price has been reduced! 2024/2/8 sales price 1,000 yen Compatible replacement needle for AUREX MM cartridge C-550/2. The standard needle is a carbon fiber cantilever, which is presumably made of metal. Sound was made using C-550/2 (Takahashi Nobuyuki)
Maintenance information: 2024.2.8 operation confirmed (sound output on C-550/2)
Accessories: none
Unspecified XLR (male) to RCA (female) conversion plug only. The appearance is good with little feeling of use (Kobayashi Hitoshi)
Maintenance information: 2023.8.14 Confirmation confirmed
Accessories: none
Main specifications: No. 2 HOT
The price has been reduced. 2024/4/11 sales price 5,000 yen. Wood cabinet with unknown compatible models. The internal dimensions of the cabinet are W432 x H123 mm, there are 4 rubber feet on the bottom, and there is a hole (203 x 93 mm) with a metal grill in the center. There is a feeling of use and dullness (Kanai Hidetsugu)
Accessories: none
Main specifications: external dimensions W450 x H162 (including legs) x D267 mm 1.8 kg
Wood cabinet for TD-124 of unknown manufacturer. It can be equipped with an SME long arm. The exterior has scratches, threads, chips, etc. (Tamura Eiji)
Accessories: no accessories
Main Specifications: W597 ✕ H160 ✕ D445mm Weight 3.9 kg
You can change the position of the steel rack and shelves with casters. There are many stains, scratches, and stains on the exterior (Takimoto Yutaka)
Accessories: none
Main specifications: W540 x H1355 x D680 mm 49.6 kg (actual measurement)
TV rack with unknown details. The upper top plate is attached to glass, and there are 2 casters on the back (2 legs in the front), 1 shelf board is about 18 mm thick, and the lower dowel has 3 places at intervals of about 32 mm. There is a feeling of use such as scratches, dents, etc., and the back plate is cut off quite a bit (Takasaki Atsushi)
Accessories: 1 shelf
Main specifications: Outer dimensions approx. W800 × H500 (450 excluding casters and legs) × D400 (upper top plate 355) mm Upper inner dimensions approx. W750 × H130mm Lower inner dimensions approx. W750 × H255 mm Approx. 25 kg
*1 bottle only Speaker stand with unknown details such as manufacturer name and model. There are appearance, abrasions, and dullness (Hitoshi Kobayashi)
Accessories: none
Main specifications: W280 × H270 × D330 mm 4.8 kg (actual measurement)
A passive attenuator that uses DALE NS-2B, a non-inductive wire winding resistor. The input impedance is 10 kΩ, and the maximum attenuation is possible to approximately -58 dB. The 23-contact VOL can be attenuated at approximately -2.5 dB. It has a careful finish that focuses on solid aluminum knobs, internal wiring, and even each part. (FUJISAWA KOSHI)
Maintenance information: 2024.5.17 Operation confirmed
Accessories: No accessories
Main specifications: W112 x H68 x D155 mm (including knob terminals)
An aluminum-pressed headshell very similar to SME's S-2 and Sansui. It is a split finger type. There is a mark where the logo has come off on the front (Murakoshi Yoichi)
Maintenance information: 2024.3.7 sound output confirmed
Accessories: none
Main specifications: dead weight 9g
1 bottle sold CV4085/6267 compatible ball mesh shield code: 8Y5 L2B measurement value 56 (rejection value 33) all the prints with the white box have disappeared, but it was determined to be EF86 based on the structure and code ※ The measured value shows the GM value measured with the test machine TV-7 (Kojima Yosuke)
Accessories: white box
An Onken (Onken) style 38cm enclosure with an impressive bass reflex lined up on both sides. It adds thickness to the low frequencies and makes full use of the umami of the sound. Originally, the ALTEC 515B is mounted, and it is an enclosure that I want to assemble with a horn system to make it sound firmly. There is quite a feeling of use such as dirt, etc., and some broken screws. (Takasaki Atsushi)
Main specifications: W800 × H1023 (including casters) × D500mm Mounting hole diameter 345mm Screw pitch (diagonal) 372mm Width between splints on the back of the front baffle 410mm (actual measurement) 79.6 kg (actual measurement)
The disposal price has been reduced. Member discounts are not applicable. 2024/3/1 sales price 12,000 yen. This is a heavy weight that can be used with the Pioneer PL-70L2. If you've been looking for one, why not take this opportunity? There are dull stains all over (Murakoshi Yoichi)
Accessories: none
Key Specifications: Weight 177g
The disposal price has been reduced! (Member discounts are not applicable) 2024/5/13 sales price 30,000 yen model number, convenient for small amplifiers, etc. such as unspecified steel satin finish audio racks, spike specification LINN products, etc. There is a feeling of use on the exterior such as small scratches and dullness (Asaine Tomoho)
Accessories: none
Main specifications: size W395 x H540 x D395 mm shelf board 350 x 350 mm between shelves 105 mm weight 11.7 kg (actual measurement)
Unspecified arm stabilizer. It was used on DA-308 (Daiki Goto)
Accessories: none
Main specifications: diameter 48 mm height 49 mm weight 800 g screw hole diameter 19 mm (actual measurement)