The price has been reduced! 2024/5/10 sales price 398,000 yen Maintained! A pre-main amplifier with a built-in McIntosh traditional output transformer. You can enjoy the rich and rich sound world typical of Macintosh. This is one that combines the sound appeal of modern and old McKinn. The sense of power that makes you feel the strength is similar to that of a separate amplifier. As for the exterior, there is some rust on the top plate. Serial JMC1488 (Fujisawa Yukishi)
Maintenance information: 2024.5.10 Maintained (VR part gearbox with motor disassembly, cleaning grease replacement. Meter and panel lamp, grommets, and tact SW replacement. Screw replacement. Cleaning volume, loudness, etc. Solder correction. Bias and offset checks. Output audio check. Remote control operation check)
Accessories: remote control, copy of instruction manual
Main specifications: 150W+150W (8/4/2Ω) phono input MM dimensions W445 x H179 x D508 mm weight 30 kg
A classic MC boost transformer. With 2 input systems, the impedance can be switched to 3.40 ohms, and a PASS line is included, so you can freely enjoy various cartridges and tone arms. You can see the exterior, dullness, stains, and feeling of use (Kobayashi Hitoshi)
Maintenance information: 2024.2.13 Operation confirmed
Accessories: none
Main specifications: MC boost transformer input 2 systems switchable, primary impedance 40 ohm, 3 ohm switching, secondary impedance 4 kΩ boost ratio 1:10 frequency characteristics 10 Hz to 100 kHz, W97 x H65 x D155 mm, 800 g
An attractive CD player with a smart design and stable playback ability while being inexpensive. You can enjoy music without getting tired with a smooth, bright tone. The exterior is generally dull and has small scratches. Serial C72PJ1136 (Yonejima Satoshi)
Maintenance information: 2024.5.28 Operation confirmed
Accessories: power cable
Main specifications: digital output/coaxial 1, optical 1 analog output/1 system W430 × H85 × D290 mm 4.4 kg
Audio-Technica connectable cartridge capsule. One can be stored while the headshell is attached. You can see a feeling of use, such as appearance, dullness, abrasions, etc. (Kobayashi Hitoshi)
Accessories: none
Main specifications: W51 x H85 x D51 mm 36.3 g (actual measurement)
Audio-Technica connectable cartridge capsule. One can be stored while the headshell is attached. You can see a feeling of use, such as appearance, dullness, abrasions, etc. (Kobayashi Hitoshi)
Accessories: none
Main specifications: W51 x H85 x D51 mm 36.3 g (actual measurement)
Audio-Technica connectable cartridge capsule. One can be stored while the headshell is attached. You can see a feeling of use, such as appearance, dullness, abrasions, etc. (Kobayashi Hitoshi)
Accessories: none
Main specifications: W51 x H85 x D51 mm 36.3 g (actual measurement)
Audio-Technica connectable cartridge capsule. One can be stored while the headshell is attached. You can see a feeling of use, such as appearance, dullness, abrasions, etc. (Kobayashi Hitoshi)
Accessories: none
Main specifications: W51 x H85 x D51 mm 36.3 g (actual measurement)
Audio-Technica connectable cartridge capsule. One can be stored while the headshell is attached. You can see a feeling of use, such as appearance, dullness, abrasions, etc. (Kobayashi Hitoshi)
Accessories: none
Main specifications: W51 x H85 x D51 mm 36.3 g (actual measurement)
※Since it is cheap, it will be handed over as is. DSD compatible network audio player. Equipped with WIFI, the D/A converter is compatible with DSD 5.6 MHz and 192 kHz/32 bit, the same as those used in super audio CD players. It is a model with high cost performance. Recommended for those getting started with network audio. There is a line wound. The remote control is out of stock (Oikawa Tetsuji)
Maintenance information: 2024.5.28 Operation confirmed
Accessories: instruction manual, power cable
Main specifications: DSD (2.8 MHz/5.6 MHz) AIFF (192 kHz/24 bit) AIFF, WAV, FLAC (192 kHz/24 bit) Apple Lossless (96 kHz/24 bit) wireless LAN standard IEEE 802.11b, IEEE 802.11g, IEEE 802.11n compliant W434 x H73 x D297 mm 2.9 kg
The price has been reduced! 2024/5/27 sales price 748,000 yen, beautiful item with original box, first arrival at Hi-Fi! A belt drive analog player equipped with a completely original tone arm and extreme performance. The combination of a newly developed original tone arm with extremely high initial motion sensitivity using knife-edge bearings, a quiet DC motor supported by a powerful power source, and a belt drive system brings an emotional playback sound with high fidelity. The exterior is generally good. Serial M30500158 (Tomonori Asaine)
Maintenance information: 2024.5.27 Operation confirmed
Accessories: original box, instruction manual, handle, hex wrench, power cable, phono cable, EP adapter
Main specifications: belt drive system, rotation speed 33/45/78, switchable platter mass 5.2 kg, tone arm type, static balance, S-shaped universal type, knife edge structure, effective length 256 mm, overhang 16 mm, compatible cartridge 4 to 11 g (17 to 24 g with attached headshell), height adjustment range 22 g, anti-skating 0 to 4 g, power supply voltage AC100V (50/60 Hz) power consumption 5W external dimensions W491 x H128 mm (from bottom to top of turntable) x D399 mm mass 24.8 kg (main body)
The price has been drastically reduced! 2024/5/23 sales price 198,000 yen ※This is a record player with Garrard 401 and Technica AT-1503/3 mounted on a 50Hz double arm cabinet. The powerful, thick, and energetic sound unique to rim drives is attractive, and you can enjoy the rich sound typical of analog. The exterior has peeling, scratches, erased characters, scratches, etc. Serial 42640 (Tamura Eiji)
Maintenance information: 2024.5.23 Maintained (dirt cleaning. Motor disassembly, inspection, lubrication and assembly. Motor spring rubber sleeve replacement. AC cord replacement Main bearing disassembly, bearing thrust replacement, lubrication, oil sealant application, assembly. idler cleaning. Speed adjustment linkage adjustment. brake adjustment. Oil felt replacement. Mounting stud bolts missing/added; nuts, metal washers, and rubber washers added. Running tests OK. (*There is a slight loud noise when turning in the opposite direction, but this is the current situation)
Accessories: No accessories
Main specifications: 50 Hz specification idler drive 33/45/78 rotation arm part: static balance type execution length 257 mm compatible cartridge 13.5 to 33 g (including shell) needle pressure range 0 to 3 g W540 x H180 x D640 mm
The price has been drastically reduced. 2024/5/9 sales price 128,000 yen Maintained in 2023/10! Late QUAD44 with CD input terminal. It's not flashy, but the thick, glossy tone is attractive. In particular, it softens female vocals. The exterior has a feeling of use such as dullness and small scratches. Serial Q031658 (Murakoshi Yoichi)
Maintenance information: 2023.10.22 Maintained (Acre sectorable terminal caulking defect? → soldering. Balance Vol, Filter Vol, SW Cleaning. AC spark killer NG, internal in-board bypass C, coupling C replacement)
Accessories: instruction manual, power cord, catalog (English)
Main specifications: 2 LINE inputs, 1 PHONO input, 1 phono sensitivity, 1m/3m/10mV switching, W321×H103×D203 mm
Maintained! Mono cartridge OFD25 initial type for EMT arms. The sound quality is clear and tight, and it has a strong thickness unique to mono. While it has a characteristic European luster that can be seen at every end of the sound quality, it reproduces the sound of the source without coloring. *Since it is mono, the output is Rch only, so please use the amplifier's mono switch. The exterior is dull. Serial 7199-00 (Yonejima Satoshi)
Maintenance information: 2024.5.25 Maintained (cantilever bending correction)
Accessories: original box
Main specifications: MC type needle tip diameter 25 μm diamond needle impedance 37 Ω (right output) needle pressure 5 g output voltage 1.15 mV frequency characteristics 30 Hz to 15 kHz tracking angle 90 degrees dead weight 33 g
Maintained! Cartridge (SHURE M44G) included. A fully automatic player with high convenience. The ease of setting is also attractive, but the location mechanism that allows you to move it to the desired position and play is convenient, so you can easily enjoy analog. There is a feeling of use such as button corrosion and dullness (Daiki Goto)
Maintenance Information: 2024.5.25 Maintained
Accessories: M44G, EP adapter, instruction manual
Main specifications: fully automatic player, direct drive, 33/45 rotation, variable needle pressure range, 0 to 3 g, compatible cartridge, dead weight 3 to 12 g (including screws and nuts), dimensions W434 x H179 x D410 mm, weight 8.5 kg
A record cleaner that indirectly imparts moisture to the case by adsorbing liquid onto the sponge inside the case. You can see the exterior, dullness, and feeling of use (Kobayashi Hitoshi)
Accessories: none
Denon high-end MC cartridges in the heyday of analog, using amorphous boron pipes. A sound with a wide range and good separation, which has a different trend from the standard 103 series. This is the reference cartridge at the time. There is slight dirt and a feeling of use. (FUJISAWA KOSHI)
Maintenance information: 2024.5.27 Operation confirmed
Accessories: instruction manual, needle cover
Main specifications: MC type output 0.2 mV 40 ohm boron cantilever solid diamond special oval needle playback band 20 to 75 kHz proper needle pressure 1.0 to 1.4 g dead weight 5.8 g
The higher model of the DL-103. Wide range was measured, and 20 Hz to 70 kHz was achieved. Delicate, wide, and powerful sound quality. There is slight dirt and a feeling of use. ※There is a note on the original box. (FUJISAWA KOSHI)
Maintenance information: 2024.5.27 Operation confirmed
Accessories: instruction manual, original box, needle cover
Main specifications: MC type output 0.2 mV playback frequency 20 to 70,000 Hz impedance 40 ohms needle pressure 1.2 g dead weight 6.5 g
Sony die-cast aluminum shell. While it is sturdy, it has a smart design and is easy to use (Oikawa Tetsuji)
Accessories: none
Main specifications: die-cast aluminum, 10.5g dead weight
The price has been reduced. 2024/5/26 sales price 228,000 yen 2023/10 manufacturer maintenance completed! The flagship stereo power amplifier model with a KT120 push-pull configuration by Sun Valley. An output transformer with a bifiler-wound custom-made by Hashimoto Electric is used. It achieves both a wide range of sound that is pleasant to listen to. This is a powerful power amplifier that can make even vintage speakers sound with modern speakers. The exterior is dull (Hiura Katsuji)
Maintenance information: 2023.10.20 manufacturer maintenance (PT replacement with a brand new product, carrying out energization after returning the remodeled point to a normal state, measurement of voltage of each part and measurement of various characteristics, music playback test)
Accessories: power cable
Main specifications: used vacuum tube KT120 push-pull 55W+55W KT120 x 4 (TUNG-SOL), 12BH7A x 4 (ELECTRO HARMONICS), CV4003 x 2 W400 x H380 x D220 mm 32 kg
The price has been drastically reduced. 2024/5/24 sales price 248,000 yen Maintained! Woofer unit used in A5. It is a 38cm Alnico magnet, and the open sound is truly Altec. There are repair marks on the edge (Sasaki Shota)
Maintenance information: 2024.5.23 Maintained (voice coil, grommet, tinsel, and connection terminal parts were polished, connected with aluminum solder, and improved contact. Edge crack repair)
Accessories: none
Main specifications: 38cm cone woofer unit impedance 16 ohms output sound pressure level 104 dB 12.4 kg
※1 bottle only. The diaphragm has been replaced with a D8R2421. It is an 8 ohm specification. Maintained! The classic model for professional 1" screwdrivers. It is installed in many of the company's 43 series, etc., and it is a driver that is easy to balance with various woofers and tweeters. The exterior has dullness and small scratches. Serial 23890 (Yonejima Satoshi)
Maintenance information: 2024.5.25 Maintained (diaphragm installation adjustment, pad dampener, mounting screw rust replacement. Material terminal contact part cleaning, terminal dirt cleaning, insulation bushing replacement. Diaphragm dirt cleaning. (This is a genuine diaphragm, but it comes with D8R2421)
Accessories: No accessories
Main specifications: 1 inch driver, throat diameter: 25 mm, 8 ohms (3.8 ohms), 118 dB, frequency characteristics, 800 Hz to 20 kHz, crossover frequency: 500 Hz or more, 5.1 kg
*Currently sold. The output has been changed to an RCA female terminal. FR MC boost transformer using a toroidal core. Create a natural sound that makes it easy to understand the characteristics of cartridges. In addition to switching the impedance of 10 to 30 ohms, there is also a bypass position, so it is compatible with various cartridges without taking up much space. You can see the exterior, dullness, and feeling of use (Kobayashi Hitoshi)
Maintenance information: 2024.5.21 Operation confirmed
Accessories: copy of instruction manual, connection cable
Main specifications: impedance 10 ohm/30 ohm/PASS playback frequency band 20 Hz to 30 kHz W64 x H64 x D105 mm approx. 455 g
This is a boost transformer (Type L version) for FR low impedance MC cartridges. There is a sense of clarity, and the clean, straight sound is attractive. There are small wounds and dullness (Oikawa Tetsuji)
Maintenance information: 2024.5.26 Operation confirmed
Accessories: none
Main specifications: input impedance 3 ohms or less, output impedance 47 to 50 kΩ, W158 x H60 x D120 mm, 2.1 kg
The price has been drastically reduced! 2024/5/11 sales price 128,000 yen Maintained! Late QUAD44 with CD input terminal. It's not flashy, but the thick, glossy tone is attractive. In particular, it softens female vocals. Serial Q36114 (Fujisawa Yukishi)
Maintenance information: 2024.5.11 Maintained (internal power supply switch contact dirt contact polishing treatment, balance VOL cleaning ~ check OK. Check the other boards and re-solder the holes. (C, R check OK)
2024.5.9 Internal power supply switch contact polishing treatment
Accessories: power cord
Main specifications: 2 LINE inputs, 1 PHONO input, 1 phono sensitivity, 1m/3m/10mV switching, W321 x H103 x D203 mm, 4.0 kg
Maintained! The classic model for professional 1" screwdrivers. It is installed in many of the company's 43 series, etc., and it is a driver that is easy to balance with various woofers and tweeters. The exterior has rust and paint peeling due to aging. ※The diaphragm is DR16R2421. (YONEJIMA Satoshi)
Maintenance information: 2024.5.25 Maintained (diaphragm installation adjustment, pad dampener, mounting screw rust replacement. Material terminal contact part cleaning, terminal dirt cleaning, insulation bushing replacement. Diaphragm dirt cleaning. This is a genuine diaphragm, but it comes with DR16R2421. DCR (A/7.1 ohm diaphragm scratch) DCR (b/6.3 ohm diaphragm scratch))
Accessories: No accessories
Main specifications: 1 inch driver, throat diameter: 25 mm, 16 ohms, 118 dB, frequency characteristics: 800 Hz to 20 kHz, crossover frequency: 500 Hz or more, 5.1 kg/piece
Maintained! The successor to the C-220, which was particular about the phono equalizer. Models from the heyday of analog are notable models that focus on records. The deep, authentic sound quality of PHONO with good sharpness is attractive. The exterior is dull and has small scratches. Serial C4X515 (Yonejima Satoshi)
Maintenance information: 2024.5.25 Maintained (contact cleaning due to poor main volume and balance volume. Due to poor contact with the compensation center switch in the sealing door, disassembly contact polishing contact grease was applied. Electrolytic capacitor replacement near the heating unit. (Check the operation of each input/output)
Accessories: power cord, copy of instruction manual
Main specifications: PHONO (MM/MC) line input 5 systems W466 x H153 x D385 mm 9.7 kg
NAGAOKA stylus cleaner. This is a standard cartridge cleaner product and an easy to use and convenient item. It's a volatile and safe cleaner. About 80% of the remaining amount is left (Yamato Yuki)
The price has been reduced! 2024/5/17 sales price 39,800 yen manufacturer maintained! A pre main amplifier with excellent cost performance. Even though it's an entry class. It has a thick, well-balanced sound and sounds well. It is one that makes you feel particular about functionality, such as having a pre-out terminal and being compatible with bi-amplifiers. The exterior is scratched and dull, and has a slight tobacco smell. Serial 9111550397 (Yamato Yuki)
Maintenance information: 2024.5.17 maintained (SP relay replacement amplifier board inspection loudness, source direct SW rework sound test)
Accessories: Power cable, copy of instruction manual ※ remote control missing
Main specifications: rated output 70W+70W (8Ω) 140W+140W (4Ω) playback frequency band 5Hz to 100kHz W434 x H134 x D407 mm 14.6 kg
The price has been reduced. 2024/5/16 sales price 64,800 yen A woofer unit equipped with an SMC magnetic circuit that achieves significant reduction in distortion by adopting SMC material (soft magnetic compound) for the pole piece part of the magnetic circuit is mounted. You can enjoy the small yet highly textured sound of Dali. There are dull stains on the exterior and edge cone paper, and a feeling of use such as dullness and small scratches can be seen (Kobayashi Hitoshi)
Maintenance information: 2024.5.11 Operation confirmed
Accessories: saran net
Main specifications: 4Ω 87dB4 59Hz to 27kHz W195xH351xD297mm 7.8 kg
Maintained by the manufacturer! Comes with an M44G cartridge and is ready to use. A new dust cover has also been created. A fully automatic player with high convenience. The ease of setting is also attractive, but after all, the repeat function and location mechanism that allows you to move the tone arm to the desired position and perform without touching it are convenient (Sasaki Shota)
Maintenance information: 2024.5.23 manufacturer maintained (arm disassembly repair, arm position detection CDS replacement, lead-in adjustment, sound output test. (Create a new dust cover)
Accessories: cartridge (SHURE M44G) manual copy EP adapter
Main specifications: fully automatic player, direct drive, 33/45 rotation, variable needle pressure range, 0 to 3 g, compatible cartridge, dead weight 3 to 12 g (including screws and nuts), dimensions W434 x H179 x D410 mm, weight 8.5 kg
Everything from the motor power supply to the tone arm has been fully maintained! New dust cover created! A player with a long-arm Ortofon AS-309S mounted on a TD-127. It comes with a dedicated optional weight, so you can use heavyweight cartridges such as SPUs. It has a high ability as a system, and it is a player that can play vividly regardless of genre, from classical to rock ※ The lifter works electrically, but since there is no sensor on the tone arm, auto stop or auto lift up is not possible (Oikawa Tetsuji)
Maintenance information: 2024.5.22 Maintained (deteriorated parts on the board, semi-fixed VOL for rotation speed adjustment, semi-fixed VOL replacement for sensor sensitivity adjustment. Front panel pitch adjustment VOL disassembly/contact polishing. Resolder the board. Disassemble and clean the arm. Drive belt replacement. Indicator lamp replacement. Grease up the platter bearing. Lubricate the motor shaft and disassemble and clean the clutch part. Floating, turntable rotation speed check, arm needle pressure check. Check the sound output. Chassis cleaning. (Comprehensive operation confirmation inspection)
Accessories: copy of instruction manual, optional weight
Main specifications: belt drive floating suspension 33/45/78rpm turntable 30cm zinc alloy 3.2kg double 16-pole synchronous motor speed fine adjustment range ± 6% W555 × H200 × D460 mm 20.4 kg
※Whether it is a genuine product is unknown. Set of 8 1 pair of JBL speaker mount parts There is a lot of feeling of use, such as appearance, dullness, abrasions, etc. (Kobayashi Hitoshi)
Accessories: none
Currently sold. The tuner's auto tuning is not working, but the current situation is. This K series CD/USB receiver is compatible with playback of iPods/iPhones, USB memory devices, etc. This is a flat, unobtrusive amplifier with a straightforward sound. It can also be connected to a PC and is recommended for those who want to get started with desktop audio. Appearance, dullness, small scratches, and a feeling of use can be seen (Kobayashi Hitoshi)
Maintenance information: 2024.5.19 operation confirmed (tuner auto tuning not working, other operations confirmed)
Accessories: remote control, power cord
Main specifications: 50W+50W W245 x H104 x D309 mm weight 5.7 kg
The disposal price has been reduced. Member prices are not applicable. 2023/5/13 sales price 250,000 yen*The main volume, BASS, and TREBLE knob textures are different from the original. Internal parts have been thoroughly reviewed and maintenance has been carried out! This is a control amplifier from Sony's high-end brand, the Esprit series. Straight sound with a sense of speed similar to the TA-E900. The outline is clear and the sound image is drawn clearly. It is a vintage speaker and is especially recommended for jazz and rock fans. On the exterior, in addition to dullness and small scratches, there is a feeling of use, such as sticker marks on the top plate. Serial 200616 (Hiroki Aso)
Maintenance information: 2023.3.4 maintained (running test by refining the I/O board and screw parts) 2022.10.1 maintained (condenser semi-fixed resistance relay LED lamp IC spark killer Capricorn washer replacement implementation all SW VR disassembly cleaning board solder surface re-solder input/output waveform confirmation and left and right balance confirmation comprehensive operation test)
Accessories: copy of instruction manual
Main specifications: 2 PHONO inputs, 5 line inputs, 2 pre-out systems, W480 x H105 x D465 mm, 12.5 kg
Maintained by the manufacturer! A special edition model of VRDS-10. This is the only TEAC player model that uses a Philips TDA1547 as a D/A converter. The sound quality is not sharp due to the hardware of VRDS, and the sound quality is well-balanced, which brings out the characteristics of the relaxed DAC7. The exterior has small scratches and a feeling of use such as dullness. ※There is a noticeable scratch on the front panel. Serial 30300 (Yamato Yuki)
Maintenance information: 2024.4.26 Maintained (inspection of each part carried out, tray belt clamp, belt turntable bearing wear, replacement pickup, and mechanical part cleaned and lubricated.
(Check operation)
Accessories: instruction manual copy remote control (for VRDS-15)
Main specifications: 2-channel CD player frequency characteristics 1 Hz to 20 kHz 8 times oversampling 20 bit digital filter W442 x H149 x D331 mm 11 kg
Full maintenance from capacitor replacement to re-soldering of each board, etc.! The first memorable luxury model in the Sansui 07 series in the era when there was no 907. Starting with the newly developed dual FET at the time, the company's consistent commitment to adopting quadruple detent volumes and large electric power transformers independently on the left and right has already been established. Compared to models from the 80s and 90s, the sense of fulfillment in the phono section is amazing. There is a feeling of use due to appearance, dullness, abrasions, etc. (Kobayashi Hitoshi)
Maintenance information: 2024.4.16 Maintained (capacitor, semi-fixed resistor, transistor, resistor, protection relay SP terminal, heat dissipation sheet replacement. SW type terminal cleaning, contact grease coating. Re-solder flux cleaning for each board. Each circuit adjustment, RCA terminals, interior and exterior cleaning. (Various tests)
Accessories: copy of instruction manual
Main specifications: 85W+85W W430 x H168 x D389 mm 16.8 kg
Maintenance has been completed, such as replacing capacitors and replacing deteriorated parts! It is a famous machine with a velvet transformer, and you can enjoy rich sound with stable operation. The fresh, glossy tone in the mid-high range has a different appeal from the MC275. The exterior has a feeling of use over time, such as dullness and small scratches (Hiroki Aso)
Maintenance information: 2024.5.19 Maintained (volume curing improvement treatment for TWIN, 2W oil capacitor replaced with 0.01μF, 3W oil capacitor replaced with 0.5 μF, missing thermistor, replacement, 250μF, domestic CE replacement, block capacitor 100/30 μF defective replacement, oil capacitor 0.22 μF defective replacement electrolytic capacitor 20μF, etc. Deterioration replacement resistor 2W deterioration replacement Vacuum tube socket and RCA jack caulking repairs ※ Other operation checks have been performed (measured at 41 to 58 W with rated output AC 100 to 117 V, SP: 8 Ω) ※ The power transformer groans a little, but there is no problem with performance)
Accessories: A copy of the English instruction manual
Main specifications: 40W+40W 6L6GCPP vacuum tube 6L6GC × 4 12AX7 × 3 12AU7x2 12BH7 × 2 frequency characteristics 16 to 40,000 Hz dimensions W400 × D265 × H195 mm weight 25 kg
Fully maintained! The main part of the SQ38F is an independent power amplifier, the famous MQ60. The natural, smooth sound quality with a high sense of transparency is attractive. You can relax and enjoy classical music and vocals in a natural way. The deep sound quality that cannot be expressed with the latest vacuum tube amplifiers is exceptional. The exterior has dullness, small scratches, and paint peeling. Serial 473753 (Hiroki Aso)
Maintenance information: 2024.5.19 maintained (vacuum tube socket block capacitor electrolytic capacitor oil capacitor SP and RCA terminal semi-fixed VR fuse holder replacement load test (8Ω load 1kHz 30W/30W) input/output waveform confirmation sound output check performed impedance switching SW gain VOL disassembly contact refinement oxidation and sulfidation prevention grease coating input/output waveform confirmation load test (1 kHz) (Sine wave at 8Ω load: 30W+30W) sound output test)
Accessories: copy of instruction manual
Main specifications: output 30W+30W dimensions W410 x H160 x D205 mm weight 13.8 kg
YAMAHA speaker stand The compact stand is made to feel stiff, and you can expect tight sound quality. It can be used for small speakers such as the NS-10M and medium speakers. There are line marks, threads, and tape marks on the exterior (Tamura Eiji)
Accessories: No accessories
Main specifications: W270 x H494 x D350 mm top plate part W190 W x D175 mm 7 kg/unit
※Since it is cheap, it will be handed over as is. A mixer with an effect loop that can mix 3 channel inputs (microphone or line) and 3 stereo line systems. The exterior has dullness and scratches. Serial M1007000864 (Tamura Eiji)
Maintenance information: 2024.5.19 simple check OK (details will not be checked)
Accessories: No accessories
Main specifications: W483 x H44.5 x D152 mm weight 2.8 kg
Choke transformer 3H/210mA DC resistance 55Ω (actual measurement 52.9 Ω) W50 x H82 x D57 mm approx. 0.8 kg (actual measurement, not including protrusions) original box, with TANGO badge (Kojima Yosuke)
Accessories: original box, TANGO badge
Maintained. An impressive pre-main with a glossy, elegant sound. The advantage of being equipped with MOS-FET is that visibility is good, and the good balance without feeling a sense of loss in sound is attractive. It is a model that can be enjoyed regardless of genre. There are small wounds and dullness (Oikawa Tetsuji)
Maintenance information: 2024.5.19 maintained (speaker relay replacement, push SW replacement due to sound interruption when switching MUTING switches, replacement volume with replacement volume for sound output, other INPUT selector electric SW, Cartrich LOADSW, speaker rotation switch, direct INPUT switch, polishing and cleaning grease application for each disassembly contact, DC balance DC bias adjustment, due to large internal dirt (Since it is a VR replacement for cleaning and volume, the volume cannot be changed with the remote control since it is not electric)
Accessories: copy of instruction manual
Main specifications: 100W+100W (8Ω) W470 × H165 × D435 mm 21.3 kg
Maintained! A network using excellent parts such as high-voltage nonpolar capacitors and coils using low-loss Orient Cores. The cross is easy to use at 500 Hz, and it is a very easy to use network for those who are assembled with drivers such as 375 (Asaine Tomoho)
Maintenance information: 2024.5.16 Maintained (12 terminal terminal mounting screws, 24 insulation bushings, terminal part cleaning, main unit internal check, attenuator VR replacement, crossover check)
Accessories: none
Main specifications: 2 way network, 500 Hz, 8 ohms
※1 bottle only. Woofer for the famous Japanese instrument 2S-305. The Alnico magnet makes a pleasant low frequency. How about for repairs or for a new system? The urethane part is defective due to deterioration. (FUJISAWA KOSHI)
Maintenance information: 2024.5.18 Operation confirmed
Accessories: No accessories
Main specifications: Alnico magnet, 30 cm, 8 ohms, 20 W, 40 Hz to 1500 Hz, diameter: 313 x depth: 168 mm, weight: 8.5 kg
Maintained! The classic model for professional 1" screwdrivers. It is installed in many of the company's 43 series, etc., and it is a driver that is easy to balance with various woofers and tweeters. The exterior has dullness and small scratches. Serial 60878/74750 (Tamura Eiji)
Maintenance information: 2024.5.18 Maintained (diaphragm installation adjustment. Pad dampener, mounting screw rust replacement Wiring terminal contact part cleaning, terminal dirt cleaning, insulation bushing replacement. Diaphragm dirt cleaning, internal wiring cable replacement. DCR (74750/6Ω diaphragm no scratch) DCR (60878/5.7Ω diaphragm no scratch))
Accessories: none
Main specifications: 1 inch driver, throat diameter: 25 mm, 16 ohms, 118 dB, frequency characteristics: 800 Hz to 20 kHz, crossover frequency: 500 Hz or more, 5.1 kg
Choke transformer 0.9 H/260 mA DC resistance 26.8 ohm (actual measurement) choke transformer mounted on A3600, etc. W55 x H71 x D50 mm 0.7 kg (actual measurement, not including protrusions) There are scratches and paint peeling in places (Kojima Yosuke)
Accessories: none
※Sold as 1 piece output transformer for single output 7W hammer tone color primary: 5 kΩ secondary: 4-6-8 Ω W50 x H81 x D58 x 57 mm 0.86 kg (actual measurement, not including protrusions) with original box (Kojima Yosuke)
Accessories: original box
Power transformer primary: 100V secondary: CT-6.3V/3A x 2, 5-6.3V/3A, 350-310-40-0-310-350V/20mA DC200mA W104 x H92 x D88 mm approx. 4 kg (actual measurement, not including protrusions) There are small abrasions and paint peeling in places (Kojima Yosuke)
Accessories: none
※Only 1 output transformer push-pull output primary: 4 kΩ Secondary: 4-8-16 Ω W53 × H65 × D69 mm 0.8 kg (actual measurement, not including protrusions) There are paint peeling and rust spots in places (Kojima Yosuke)
Accessories: none